I was searching for antique dressers on Pinterest when I unearthed individuals utilizing them as vanities,” says peruser Caleb Kettler, who chose to make one himself. “The trickiest part is fitting in the pipes.” In fact, to clear a path for the trap, you’ll need to adjust the drawers. Who better to show how to do that than This Old House ace woodworker Norm Abram?
Presently, his rendition of the venture is entirely included; the dresser here is altogether bended openings, and it got another top of marble with a drop-in sink, requiring more alterations. You can make a simpler go of it by thudding a vessel sink appropriate on top of a rectilinear piece.
In any case, the approach is the same. See with your own eyes as Norm strolls you through the means to including a genuinely unique point of convergence to your shower, all while protecting a valuable piece of drawer space.
On this dresser, the upper drawer must be expelled to permit space for the drop-in sink. That implies the drawer confront needs to fall off and be reinstalled later to make a false front. Clip the drawer to a work surface and utilize the trim saw or handsaw to cut at the edges of the drawer where they meet the face, as appeared.
Flip the drawer topsy turvy and fit the swaying multitool with a flush-cutting sharp edge or snatch a handheld flush-cutting saw. Decreased side of the drawer front, where the base meets it, keeping the sharp edge cozy against it. Put aside the drawer front and in addition the parts of the drawer outline—you’ll utilize them in Step 5 to change the lower drawer. Utilize the bore/driver to unscrew the dresser top.
To account for the pipes, you’ll have to incorporate a set pattern with no less than one of the drawers—for this situation, the lower one. Rest the drawer topsy turvy on your work surface, and measure and stamp spots 4 crawls to one side and left of the drawer’s centerline. Utilize the straightedge, as appeared, to draw cutlines on the base of the drawer. Exchange your imprints to the back of the drawer.
Cinch the drawer with the goal that you can take a shot at its back. Utilizing the crossbeam square as a guide, take after the cutline along the back of the drawer with the trim saw. Keep the drawer clasped, and keep taking after the cutline on the base of the drawer until you achieve the face. Utilize either the multitool or the handsaw to complete the cut and separate the set pattern where it appends to the face.
Take the upper drawer’s back and utilize the sliding T-slope to discover the edge where one end meets the front, then exchange the edge and cut the end. Hold the piece upright in the set pattern, and check it where the back of the lower drawer crosses it. The new piece will be sandwiched between the drawer front and the drawer back. Cut the piece on the miter saw. Measure, check, and cut the inverse piece.
Dry-fit the recently cut pieces. Each one in turn, expel them and run a dot of wood paste along the edges where they append; fit them set up, and secure them with the pneumatic nail firearm and 1¼-inch 18-gage brads, as appeared. Wipe away any abundance wood stick with a soggy fabric.
Tear calculated hindering from 1 stock on the table saw. Brush the right-edge edges of the obstructing with wood stick, position them between the drawer sides and face, and tack them set up.
The notched dresser drawers slid on wood manage rails. To refresh the dresser drawers with discretionary overwhelming obligation slides, introduce blocking flush between the leg confining. Initially, measure between the front and back of the dresser casing simply over the wooden guide, as appeared. Sliced a 1×4 to that length. Make 1×4 obstructing for the opposite side a similar way.
Add spacers to fill the hole between the blocking and the dresser, securing them with paste and brads. Wedge a cut 1×4 between the leg surrounding simply over the wooden guide on each side, and toenail the closures into the encircling. Utilize the mallet and pry bar to expel the old wooden drawer guides.
How to Repurpose a Dresser Into a Bathroom Vanity? Take after the slide’s establishment guidelines to position the inward rail against the side of the drawer. Watch that the equipment is square to the back of the drawer, and check the prepunched gaps on the blocking. Hold the rail set up, and secure it to the drawer with the included inch wood screws. Rehash the procedure on the other drawer side.